-
Posts
84 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Blogs
Downloads
Events
Everything posted by scoe141
-
Sidekick? Do I pull the trigger?
scoe141 replied to jackdurkin63's question in Washing, Drying, and Decontamination
I just wanted to say thanks for the suggestions on this thread. I ended up getting the Sidekick and had the chance to use it today. Couple of notes: • I love this thing. It puts out a lot more air then I realized. • Getting into the cracks is so helpful especially before waxing/polishing. • It's definitely well built. • It's not too loud, but if you have sensitive ears you may need protection. I measured the sound level which peaked at around 95 DB (close to the unit) and hovered around 80-85 DB at about an arms length away. To give you an idea, 90 DB is about the sound level of a hair dryer; 93 DB is about the level of belt sander and 98 DB is the equivalent to an hand drill. -Taken from NIOSH Also, the sound level measurements were taken with a NIOSH app on my iPhone. As it's not 100% accurate, it's pretty close. • The power cord is 18 gauge (I confirmed with Metro) and I ended up getting a 25' extension cord/14 gauge, which is perfect to get around my garage. • Using the Sidekick and the Great White MF towel dried the car really well. (There was less water on the towel afterwards.) And no water run off! • All in all I'm happy with the Sidekick. Once my car is waxed I'm sure the water will bead off a lot better while using this. It would be tough to do an entire car with it, but I knew that when purchasing it. Hope this helps anyone interested in picking up one of these! -
I'm going to have an angry wife.
scoe141 replied to Rich's topic in Product Polls, Feedback, and Company Input
How are they? I was thinking about buying one. -
If there was dead rodent in there, it, along with any remnants will need to be removed. This includes any droppings, etc. After that you may need a fogger or ozone machine to completely eliminate the odor. Before you go through all that, I'd have the car professionally looked at and inspected by a mechanic or dealership. It may cost you time, but at least at the end of the day you know you'll get it all taken care of. Good luck.
-
NEW! Adam's Microfiber Revitalizer & Brightener
scoe141 replied to Team Adam's's question in Towels, Brushes, & Accessories
Thanks Chris. I believe most of us on here are partly OCD/clean freaks, so anything that can restore a cleaning tool is well received. Me included! -
NEW! Adam's Microfiber Revitalizer & Brightener
scoe141 replied to Team Adam's's question in Towels, Brushes, & Accessories
Thanks to this thread and the testimonials, I'm adding MF revitalizer to my next order. -
How did you come to use Adams?
scoe141 replied to Audog's question in General Detailing Discussion and Questions
A few years back I bought a Subaru WRX and wanted to keep it looking as new as possible. After researching car care products I noticed Adam's received a lot of stellar reviews. (Not to mention their intuitive videos were really helpful.) After trying their products I was hooked. But what keeps me loyal is their customers service. It's truly unrivaled. -
What to do next after clay bar car?
scoe141 replied to Chris246810's question in General Detailing Discussion and Questions
You're going to do fine! I believe most of us have been in your shoes at one point or another. If you run into any issues, I'm confident one of us will be able to help you out. Shoot, I bet if you ask for help, there may be someone in your area that could lend a hand. Good luck! -
How to become a distributor
scoe141 replied to Joe_Joe's question in General Detailing Discussion and Questions
I believe there's one in Cheshire. It's called Corvette Store & More. You can call them at 203 710 9614 to confirm. -
Do you think the chemicals from the road have ate away at the mats? Have you tried contacting Weather Tech? After trying what everyone mentioned, I can't imagine there being anything else you can do. (Unless you haven't tried steam cleaning, or talking to the folks at Weather Tech.) Good luck, hope you find a solution!
-
Swirl Killer Mini- how much coverage area?
scoe141 replied to scoe141's question in Paint Correction & Polishing
My main polisher is a Flex DA. I usually set it on 5-6 when using correcting polish. When I'm applying a wax or sealant I drop it down to 3. I wasn't sure how that would be translated to the SKM. I'll be using it primarily on my front bumper (Subaru) and also around the trunk where the Flex can't reach.- 9 replies
-
- swirl killer
- skm
-
(and 2 more)
Tagged with:
-
Swirl Killer Mini- how much coverage area?
scoe141 replied to scoe141's question in Paint Correction & Polishing
Thanks Shane! Just wanted to make sure.- 9 replies
-
- swirl killer
- skm
-
(and 2 more)
Tagged with:
-
Welcome Bob. You're going to really like this forum. There's a lot of knowledgable folks here.
-
What am I doing wrong? Detail Spray
scoe141 replied to DGscatpack's question in General Detailing Discussion and Questions
How's the towel you are drying it with? If it's a MF towel, did you dry it with other towels or a dryer sheet? I know doing that could affect its proper dryer abilities. Also, you mentioned using a pressure washer to rinse it off. Does it have any soap attached to it? Just wondering if any soap residue could be getting on the car after you rinse it. -
Drying new merino wool wash mit
scoe141 replied to hemi1300's question in General Detailing Discussion and Questions
I'm not sure if the new one is anything like the old one. I've had the same one for 5~ years. After I'm done washing the car, I hose it off and place it on top of a grit guard to air dry. It's been fine since. -
Swirl Killer Mini- how much coverage area?
scoe141 replied to scoe141's question in Paint Correction & Polishing
Thanks Thor, appreciate the response!- 9 replies
-
- swirl killer
- skm
-
(and 2 more)
Tagged with:
-
Swirl Killer Mini- how much coverage area?
scoe141 posted a question in Paint Correction & Polishing
I plan on fixing up a few areas of my car (Subaru). The front bumper is all ate up and I will also need to polish the top and trunk area. While reading up on the SKM, I noticed that it isn't meant to be used on large areas. I do have a DA polisher that I'll be able to use on the rest of the car. My question is, will it hurt the machine if I used it to polish/correct the front bumper; and around the trunk area? I read that keeping it on setting 4 will prevent overheating the backing plate. Just want to make sure that I can use it for those purposes. Thanks for any help.- 9 replies
-
- swirl killer
- skm
-
(and 2 more)
Tagged with:
-
Like MC2 said, I've used APC and let them air dry. Soaking them definitely helps. Since your pressed for time, I'd suggest buying a couple extra pads. If you have access to a dehumidifier you can place the pads next to it, right side up along with a fan to help with the drying process. Let us know what you decide.
-
If you could buy only ONE Adams product......
scoe141 replied to briarpatch's question in General Detailing Discussion and Questions
APC. I've used it to clean everything from car tires to my espresso machine. (diluted of course.) -
Help me restore this (possibly) 70 year old lacquer finish
scoe141 replied to Mortimer452's question in Paint Correction & Polishing
I'm going to second Rich. I'd call Adams directly or ask someone. For that great of find, I'd hate to screw anything up. -
Found This Little Gem on YouTube
scoe141 replied to mathews31's topic in Product Polls, Feedback, and Company Input
It's like one of the few infomercials that was actually legit. -
Nice. Yea, I'd do some research, find out some good locations in your area. Make sure to post them when you're finished!
-
I'd find a clean background free of clutter, distractions etc. One of the best ways to showcase the cars is using a setup like the image above. You want to show as much as the cars as possible. What type of camera are you using?
-
Foam cannon pressure washer help
scoe141 replied to Nathan's question in Washing, Drying, and Decontamination
They're really not made for that. I know when my soap starts to run out it begins to shoot more water. That's when I disconnect it and go to the wash mitts. If you're concerned about turning off the nozzle you can always get a shut off valve. That's what I use and it makes it easier when switching hose adapters. -
Foam cannon pressure washer help
scoe141 replied to Nathan's question in Washing, Drying, and Decontamination
Hey Nathan, Adam's foam cannon has a 1/4" adapter. I believe the one you purchased is 3/8" (I'd double check). I would go to your local big box or hardware store and ask for an adapter. (Bring the parts if possible, just to make sure.) Hope this helps. And don't despair, the foam gun (cannon) is a fantastic wash tool. You'll love it.