Jump to content
Customer Service 866.965.0400

Thorsager

Members
 View Profile  See their activity

  • Posts

    748

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by Thorsager

  1. Thorsager
    Nice work and great write up!
  2. Thorsager
    Here are pictures of some of the Corvettes that came through the tent.
  3. Thorsager
    I was great to see you both again. We really did have nice weather!
  4. Thorsager
    Welcome! Any pictures of your Challenger?
  5. Thorsager
    Welcome!
  6. Thorsager
    It had the wall and the address to send the stickers to.
  7. Thorsager
    That was a great idea! I saw it on Instagram and sent ours a few days ago.
  8. Thorsager
    I would try a steamer.
  9. Thorsager
    One other option you have if you see the coating is failing is to use the Ceramic Paste Wax. It will add protection and gloss.
  10. Thorsager
    The Yukon looks good! I think you will be ok. You did use the coating prep so that may have removed some of the sealant. Worse case is the coating doesn't last as long. I would use the Ceramic Boost at least once a month to add some longevity to the coating.
  11. Thorsager
    Welcome to the forum!
  12. Thorsager
    Welcome!
  13. Thorsager
    If you have the time, equipment, and a garage I would use the ceramic coating. If not I would use the ceramic wax, which adds an incredible amount of shine!
  14. Thorsager
    Welcome back!
  15. Thorsager
    Another busy and fun Chrysler Carlisle show! It was great to see everyone who stopped by! Here are a few pictures from the show.
  16. Thorsager
    Yes you can clay and use the Iron Remover on single stage paint.
  17. Thorsager
    Welcome!
  18. Thorsager
    The next event at Carlisle will be the Carlisle Events Chrysler Nationals July 13th - 15th. We are on the midway just look for the inflated detail spray bottle on top of the trailer. We will have cars there so you can try any of the Adams products including the polishers. The next two shows after Chysler show will be the Carlisle Events Corvette show August 23-26th and then the Carlisle Events Fall show October 3-7th. Stop by and say hello!
  19. Thorsager
    Let me clarify I did apply the coating to a 2x2 section at a time, wait, and then wipe off. Then after fully completing 2 panels I backed the truck out and rechecked for high spots. Backing the truck out did add time to the job but after letting the coating cure for 24 hours I did not have any areas that needed to be redone.
  20. Thorsager
    I have started to coat 2 panels at a time then backing the vehicle out of the garage to check for high spots in the sun. I caught a lot of high spots this way on the most recent black Ram 1500 truck that I coated. I also have tried to put less coating on the applicator and work in smaller areas. I used 4-5 towels to remove the coating residue on the truck.
  21. Thorsager
    Welcome from a fellow Hellcat owner!
  22. Thorsager
    I have had my cr spotless for about 5 years. I use it after I have already rinsed the car off. We have very hard water so it helps prevent water spots.
  23. Thorsager
    I never used IronX but here is Adams Iron Remover working. The stain may have come water dripping from a pipe in a parking garage. We did not think we could get it out! After rinsing the iron deposit was gone.
  24. Thorsager
    You should have enough coating to do both vehicles. Maybe enough to start your wife's car. The applicator will not harden before your done provided that you keep going and not take long breaks. I would use two towels to remove the coating on vehicles that big. One for the initial removal of coating and a second to go over the area again in case you missed anything. You could rewash to help remove the polish then use the coating prep or just use the coating prep. I have done both and cannot see a difference in the coating. Post some pictures when you are done!
  25. Thorsager
    It does leaves the surface slick.
×
×
  • Create New...