Beemer

No, you do not need to discard them, just don't use them on the body of a vehicle.  Use them for engine bay cleaning, the insides of wheels, exhaust pipes or anyplace that is not polished like the body is.

To mark mine for non-body usage, I cut the corners off the towels along with storing them separately to ensure no cross contamination.  Furthermore, since they are non-body towels, I hand wash them since they can get nasty with the areas I use them on.

I do this every time.  I mix a big pressure bottle with Rinseless Wash and pre-spray before I do a multi-towel Rinseless.
 

The new formula will NOT release until AFTER you have purchased a gallon of the current formula.
 
Just my experience.....                               <grin>
 
 

The new formula will NOT release until AFTER you have purchased a gallon of the current formula.
 
Just my experience.....                               <grin>
 
 

Been too busy on house projects.
 
Home Theater wall is done.
 

 
Workshop coming along, took a long time to get all the cabinets with them being out of stock.
 

 

 
Landscaping almost finished.  Hauled in lots of good dirt.  Record setting heat this summer has not been fun.
 

 
Next project is the detailing area.  Cabinets and sink are in, but need to get the pressure washer, hose reels and deionizer transferred from my cart to the wall.  Once that is done, I can focus on getting this thread back on track with detailing posts!
 

While we do get reps from Adam's chiming in here from time to time this is really a user-to-user forum.
 
Your best bet is to contact customer service via voice or email.  They should be able to help you.
 

While we do get reps from Adam's chiming in here from time to time this is really a user-to-user forum.
 
Your best bet is to contact customer service via voice or email.  They should be able to help you.
 

Call customer service and i guarantee they'll make it right.  But you have to call.  They can't do it here.
 

here ya go..

I do this every time.  I mix a big pressure bottle with Rinseless Wash and pre-spray before I do a multi-towel Rinseless.
 

New garage build is underway!  The last 10 months have been super busy, getting the old house ready to sell, and then starting on a new house build.  Yeah, the garage will have a house attached to it, but the priority is the garage!
 
In the old garage, I had a pretty good setup for detailing and also woodworking, but the lack of separation between the two hobbies was a bit of a hindrance.  I needed more room around my truck, to be able to open the doors wide.  I also wanted to be able to wash inside, to avoid the constraints of weather, but the shop tools cannot get wet.
 
A few pics of the old garage, all cleaned up for the sale:
 

 

 

 

 
I had hoped to find a buyer who would want the shop tools along with the house, as I spent many hundreds of hours getting this shop setup. The buyers ended up being a couple older ladies, and they had no need for tools, so I spent another hundred hours disassembling the shop and getting all the tools moved to a storage unit.
 
The new garage will have room for three vehicles, and I made it wider, with an 18-foot double door and 10-foot single door.  First order of business was floor drains for washing inside, and also for all the winter lush that ends up falling off the vehicles in the heated garage.  With the trench drains in each parking stall, and the floor sloping to each drain, all the winter crud will fall off and run under the vehicles, rather than across the floor to the doors.
 
The builder on this house is an engineering client of mine, which gave me the fortunate opportunity to do some work myself during the build.  I installed the drains and piping, with a small catch basin just outside the garage to collect the dirt.  The pipes drain to the rear of the lot to a small swale, and also pick up the rain gutter downspouts.
 

 

 

 
The new layout has a Workshop area off the rear of the garage where some of the woodworking tools will go, and then there is a basement below the Workshop which is accessible from the back yard, and some tools and storage will go there.  While it is not ideal to have tools in two different locations, the size and layout of the sloped lot would not allow for the main garage to be any bigger.
 

 

 

 
The Workshop will get flooring, and some cabinets with workbenches The table saw will go under the duct dropping from the ceiling, with the dust collector down in the basement.
 
Building a garage from the beginning gave me the ability to get it roughed-in for dust collection and compressed air, pick the locations of all the outlets, have wall mount garage door openers, and get blocking installed for the fans, hose reels, and pressure washer shelf.
 

 

 
 
A few pics of the house, which will be completed by the end of March.
 

 

 

 

 
 
 

Good advice above. I'll put it this way...
 
When it comes to paint correction and using words like "have to" and "necessary," the real answer is no. <Insert quote about nothing before the word "but" matters> But...  Proper prep will help get the best possible, longest lasting results. Many on here, myself included, will recommend the full suite of prep before applying a coating. Know that when using coatings, regular ceramic or Graphene, you're locking in whatever is there for potentially years to come, depending on version. Paint condition is fairly subjective, obvious damage aside, so if you're ok with the paint, it's your car. At a bare minimum, wash, decon (clay and Iron Remover), and Surface Prep it. Beyond that, only you know what you'll be satisfied with.
 
We're here to help along the way, so good luck and enjoy!

I never win anything so I'm just doing this to improve the odds for everyone else.
 
Merry Christmas!!!
 

I never win anything so I'm just doing this to improve the odds for everyone else.
 
Merry Christmas!!!
 

I never win anything so I'm just doing this to improve the odds for everyone else.
 
Merry Christmas!!!
 

Quote of the year:
 
"No telling what the stripper will do to your tires."
 
 

Quote of the year:
 
"No telling what the stripper will do to your tires."
 
 

Quote of the year:
 
"No telling what the stripper will do to your tires."
 
 

Quote of the year:
 
"No telling what the stripper will do to your tires."
 
 

Quote of the year:
 
"No telling what the stripper will do to your tires."
 
 

There's several of us having this issue.  Can't the solution be shared here?

There's several of us having this issue.  Can't the solution be shared here?

Still no fix to the icons on mobile?   Its driving me nuts with no icons!😫

How 'bout those little hair-elastic things!  My daughters cars are full of those stupid things.
 
And French fries.....
 
smh